Posts Tagged ‘electrical service’

Grilling Safety

Posted on: July 2nd, 2017 by Derek Barmer No Comments

 

If you’re planning to fire up the grill on July 4th, Labor Day or any other day this summer, make sure you don’t see fire anywhere but the grill by following some simple safety tips.

First and foremost, if you have a gas grill, check for leaks by putting a soap/water solution to the hose with a spray bottle and turning the propane on to see if bubble form. No bubbles = good. Bubbles mean that you should turn it off and check the connections. Also, check the connection points.

If you smell gas, turn off the tank and burners and get the grill serviced before using it again. If the smell continues though, call the fire department.

For charcoal grills, if you use a starter fluid, use only charcoal starter fluid. Do not use other flammable liquids. Keep charcoal fluid away from any other sources of heat.

For electric charcoal starters, you’ll likely need an extension cord as their cords are short. Keep in mind that metal parts will be very hot! Hang it up where nobody will bump into it and make sure it isn’t near anything flammable.

If the rain starts or you’re too hot, do not decide to move your grill indoors or anywhere near the house, deck or low-hanging branches.

Keep excited pets and children away from the space around the grill and always have someone watching the grill.

Always clean your grill after using it so that grease or buildup doesn’t stick.

Let coals cool completely after you are done grilling, and then dispose of them in a metal container.

###

Have a concern with your electrical, plumbing or air conditioning? Central Carolina Air Conditioning, Plumbing and Electrical is here to help! We offer 24 hour emergency service 7 days a week!  Give us a call! 1-800-461-3010 to speak with our customer service agents that can answer your questions or schedule an appointment!

How to Mount a TV

Posted on: June 11th, 2017 by Derek Barmer No Comments

 

Central Carolina Air Conditioning, Heating, Plumbing, and Electrical mounting a tvIt’s a project you’ve likely been thinking about for awhile if you haven’t done it already—mounting your TV to the wall. It looks so clean and takes up less space than a TV on a stand. So let’s get to it!

Look for a spot on the wall with no glare and good visibility, and pick a good sitting height (usually with the center of the screen 40-45 inches off the floor). Make sure there is an electrical outlet nearby!

 

Look for the mounting holes on the back of your TV. If needed, take off the plastic caps over the holes. If there’s a stand on the frame, remove it. Attach the mounting arms to the mounting holes on your TV, and make sure the mounting brackets are level with each other.

Use a stud finder to find the two studs in your wall that will support your TV. (Hollow wall anchors will not work.) Use a pencil to mark each stud’s center, and a nail to confirm a stud has been located. Measure the distance between the top and bottom holes on each TV mounting arm, then mark two points in the center of each wall stud. Drill pilot holes for the wall bracket screws or bolts. Attach the wall bracket plate to the wall using the screws or bolts provided.

Lock the TV mounting arms onto the wall bracket plate. Follow the manufacturer’s instructions to secure the connections. It may be easier to connect the cables to the television before attaching it to the wall bracket if you’re attaching your TV flat to the wall to a fixed wall mount. Do not attempt this last section without help from another person.

###

Have a concern with your electrical, plumbing or air conditioning? Central Carolina Air Conditioning, Plumbing and Electrical is here to help! We offer 24 hour emergency service 7 days a week!  Give us a call! 1-800-461-3010 to speak with our customer service agents that can answer your questions or schedule an appointment!

 

Wiring Your Unfinished Garage

Posted on: April 2nd, 2017 by Derek Barmer No Comments

 

You’re looking around at your unfinished garage and realize you need more outlets and lighting. Before getting started, keep a few things in mind: If you are leaving the walls and ceiling open, you’ll have to use the framing members to protect and support the wires. Do not span stud or joist spaces with wires, and keep the cables closely hugging the studs, plates and ceiling joists.

Always make sure you’re doing everything safely and up to code. If you’re just not sure, don’t hesitate to bring in a professional electrician. Lastly, if you plan to close up the walls later on, you’ll have to rewire. So, what’s next?

You’ll route the cable along studs, top plates and ceiling joists, along the framing member that leads to the next box. Keep cables on vertical surfaces—not on the tops of walls. Plan your wiring and put up all the electrical boxes.

Next, run a cable from one box to another by pulling cable off the coil, stripping at least 8 inches of sheathing off the wires and threading the wires and about 1/2 inch of sheathing through the wire opening in the box.

Untwist the cable and staple, staple, staple! Do this at least every 4 feet to the framing, preferably more.

When you get to the next box, stretch out the cable and mark the entrance point on it, cut the cable about a foot long, strip the sheathing and feed the wires into the box. Nail in the staples near the box.

NOTE: You’ll have to hold all wires at least 1-1/4 inches from the back and front surface of studs and joists.

Electrical boxes may have metal or plastic cable clamps that are built in. Many duplex boxes only have knockouts. Staple cable within 8 inches of boxes without clamps and within 12 inches of boxes with clamps.

And don’t forget: If your garage has a wall made of concrete or is already dry walled, cable installed on these exposed surfaces has to be protected by conduit.

Have a concern with your electrical, plumbing or air conditioning? Central Carolina Air Conditioning, Plumbing and Electrical is here to help! We offer 24 hour emergency service 7 days a week!  Give us a call! 1-800-461-3010 to speak with our customer service agents that can answer your questions or schedule an appointment!

Reduce Laundry Energy Costs

Posted on: March 23rd, 2017 by Derek Barmer No Comments

 

An easy way to reduce your energy costs is to change the way you do your laundry. What are some changes you can make to reduce your carbon footprint and put money back into your wallet?

With the warmer weather coming, try line-drying your clothing instead of using the dryer. Drying accounts for up to 90% of laundry energy. If drying outdoors will not work for you, look around your home and see where you can put a drying rack or clothesline. Even if you only hang a few items, it’s better than nothing! You can even hang a few items on your shower rod. Choose the fastest spin cycle on your washing machine to get as much of the water out as you can. Keep racks away from the walls to prevent mold and don’t put items too close together so they dry quickly.

Maintain your dryer. Clean out the lint filter after each use, and deep clean your dryer (including the tubing) once a year. Use the automatic setting instead of the timed setting to avoid over drying.

As for your washer, about 80% of the energy it uses is for heating the water. Wash clothes and other items in cold water as much as possible. This will also help them to last longer. If you need more cleaning, then use a warm pre-soak then wash cold. Wash full loads as much as you can.

If you’re looking to buy a new washer and dryer, look into ENERGY STAR models. These typically use 25% less energy and 45% less water!

A few extra tips: reuse clothing as much as you can before washing, and don’t dry heavy materials or towels with lightweight items.

Have a concern with your electrical, plumbing or air conditioning? Central Carolina Air Conditioning, Plumbing and Electrical is here to help! We offer 24 hour emergency service 7 days a week!  Give us a call! 1-800-461-3010 to speak with our customer service agents that can answer your questions or schedule an appointment!

Deep Clean Your Dryer

Posted on: March 6th, 2017 by Derek Barmer No Comments

 

To keep your dryer running efficiently and to help keep your family and home safe from a potential dryer fire, thoroughly clean it annually. This is a great project to tackle on a weekend afternoon. Improper dryer ventilation causes 14,000 fires each year!

Over time lint builds up in the inside of your dryer, especially around the drum. With most dryers you can remove the top or front panel by simply removing a few screws, and take your extension on your vacuum to it.

Next up, your dryer ducts. This part is a bit trickier. Unplug your dryer and remove the flexible duct from the back of the dryer with your screwdriver. Use a large cleaning brush to push out any lint from behind your lint trap. Reach into the hole and pull out any buildup and vacuum again there and in the tubing. Be careful with using any sharper tools to get to the middle of the tubing, as they could puncture it. Typically, there is more buildup towards the ends.

Also vacuum where the duct exhaust exits your house. If you find that you have issues with birds/critters, install a bird guard on the outside. Make sure that the screen is not covered with lint, which will prevent any airflow.

Lastly, slide the clamp over the vent to attach and then put the dryer back into place. Run dryer on air fluff for about 10 minutes to let the debris that may be loose escape.

Have a concern with your electrical, plumbing or air conditioning? Central Carolina Air Conditioning, Plumbing and Electrical is here to help! We offer 24 hour emergency service 7 days a week!  Give us a call! 1-800-461-3010 to speak with our customer service agents that can answer your questions or schedule an appointment!

Wiring for Your Home Office

Posted on: January 3rd, 2017 by Derek Barmer No Comments

 
imagesMore and more people are working from home. You can have the best speed and performance in your home office if you set everything up properly and don’t cut corners.

You’ll likely need high-speed Internet and networking. Structured wiring is a data delivery system that can carry phone, fax, broadband, networking, and video/television technologies. The system has three parts: a panel where outside service enters the home, wires and cables throughout the house, and connecting hardware. You can get a prepackaged system, but that means you may have wasted outlets or no outlet where you need one. It is a good idea to develop a home-office plan before you wire. Figure out where the computer, printer, phones, and media will be set up and where conference calls will happen.

The system is installed the same way regardless of whether you have a new construction or are remodeling. The preferred method is the “star” layout, where each outlet extends individually to the service panel. This will allow for flexibility and help to figure out any problems. There are options for older homes so you don’t have to open up walls. Wires can be fished through walls.

If you’re not comfortable doing such a big project on your own, hire a professional. Not only do you want it to be installed correctly but you also want to make sure you have create necessary flexibility to accommodate future expansion. Costs vary, but the system typically ranges from about 1 to 3 percent of a home’s value.

Have a concern with your electrical, plumbing or air conditioning? Central Carolina Air Conditioning, Plumbing and Electrical is here to help! We offer 24 hour emergency service 7 days a week!  Give us a call! 1-800-461-3010 to speak with our customer service agents that can answer your questions or schedule an appointment!

Updating Your Kitchen for High-End Appliances

Posted on: November 21st, 2016 by Derek Barmer No Comments

pexels-photo-213162

Professional-style kitchen appliances are becoming increasingly available and popular in everyday homes. If you’re considering upgrading your kitchen by installing these types of appliances, there are some things to consider and tips to make sure it’s all done safely.

First, think about your kitchen size. Many kitchens will simply be too small for these items. You will need about three feet of space for the refrigerator, three feet of freezer space and four to five feet for a commercial-style range. Also, some of the ranges are very heavy and require a special base. Many manufacturers do offer smaller models, so check their specifications.

Consider the burners and ventilation hoods. Many high-end ranges and cooktops have burners that can exceed 20,000 BTUs and require hoods that can handle up to 1,200 CFM. This is almost 10 times the typical amount. To ensure proper ventilation, add up the total BTUs of the range burners, divide by 100, and then you’ll get the number of CFMs needed. For example, a range with a total output of 70,000 BTUs should be equipped with a hood capable of moving 700 CFMs. This will help prevent issues with heat, grease, smoke and moisture.

Houses with high-power hoods may need to install an air makeup unit to replace the air that the ventilation is removing from the home. This is because the removal of too much air can be dangerous with the use of
chimneys and furnaces.

Lastly, any customizations involving electric extensions or plumbing work is best handled by a professional if you aren’t sure of what you’re doing.

Have a concern with your electrical, plumbing or air conditioning? Central Carolina Air Conditioning, Plumbing and Electrical is here to help! We offer 24-hour emergency service 7 days a week!  Give us a call! 1-800-461-3010 to speak with our customer service agents that can answer your questions or schedule an appointment!

Holiday Lights and Electrical Safety

Posted on: November 13th, 2016 by Derek Barmer No Comments

christmas wishes

Many of us are already taking out those boxes of holiday decorations or starting to shop for new décor. With all of the lights, though, come safety concerns. How can you make sure you’re lighting up your home without risking fires or electrical injuries?

  • Before getting started, plan your displays. Look for outlets and figure out what you can reasonably do before you go into a decorating frenzy.
  • When shopping, make sure the product has a label showing that it has gone through independent testing by a recognized lab, such as UL or ETL.
  • LED lights are more energy efficient, last longer and are more durable than incandescent lights.
  • Don’t use items intended for outdoors inside, or vice versa.
  • Make sure you’ll be notified of any recalls by sending in the product registration forms.
  • Inspect older decorations for any loose or damaged wires or connections.
  • Unplug before replacing bulbs or fuses.
  • Make sure cords are not pinched in windows, doors, etc.
  • Don’t overload electrical outlets with too many items at once.
  • Do not connect an extension cord to another extension cord or place them in high traffic areas or under furniture, carpets or rugs. Do not run them through walls or ceilings.
  • Do not connect more than three strands of incandescent lights together.
  • Outdoor lights should be plugged in to circuits that are protected by ground fault circuit interrupters (GFCIs).  (You can buy portable GFCIs.)
  • Protect lights from the wind by fastening them to firm surfaces but make sure this is not done in a way that could damage the cord’s insulation.
  • Turn off all holiday lighting before going to bed each night.

Have a concern with your electrical, plumbing or air conditioning? Central Carolina Air Conditioning, Plumbing and Electrical is here to help! We offer 24 hour emergency service 7 days a week!  Give us a call! 1-800-461-3010 to speak with our customer service agents that can answer your questions or schedule an appointment!